Difference between revisions of "Photon Development"
| Line 12: | Line 12: | ||
====Basics==== | ====Basics==== | ||
| − | (1) Photon with Headers | + | (1) Photon with Headers, |
| − | (1) USB Micro B Cable | + | (1) USB Micro B Cable, |
| − | (1) Flex antenna | + | (1) Flex antenna, |
| − | (1) Breadboard | + | (1) Breadboard, |
| − | (1) Proto-board | + | (1) Proto-board, |
| − | (1) Deluxe Jumper Wire Pack | + | (1) Deluxe Jumper Wire Pack, |
| − | (10) Male to Female Jumper Wires | + | (10) Male to Female Jumper Wires, and |
| − | (1) Battery holder (4xAA, 2x2 with switch) | + | (1) Battery holder (4xAA, 2x2 with switch). |
====Headers==== | ====Headers==== | ||
| − | (5) 12-Pin Female Headers | + | (5) 12-Pin Female Headers and |
| − | (2) 40-Pin Male Breakaway Headers | + | (2) 40-Pin Male Breakaway Headers. |
====Capacitors==== | ====Capacitors==== | ||
| − | (10) Ceramic Capacitor 10nF | + | (10) Ceramic Capacitor 10nF, |
| − | (10) Ceramic Capacitors 100nF | + | (10) Ceramic Capacitors 100nF, and |
| − | (5) Electrolytic Capacitors 100uF | + | (5) Electrolytic Capacitors 100uF. |
====LEDs and Diodes==== | ====LEDs and Diodes==== | ||
| − | (5) Basic LED - Red | + | (5) Basic LED - Red, |
| − | (5) Basic LED - Green | + | (5) Basic LED - Green, |
| − | (1) RGB LED | + | (1) RGB LED, |
| − | (6) Diode | + | (6) Diode, and |
| − | (1) IR LED | + | (1) IR LED. |
====Resistors==== | ====Resistors==== | ||
| − | (10) Resistor 220-Ohm | + | (10) Resistor 220-Ohm, |
| − | (10) Resistor 1K-Ohm | + | (10) Resistor 1K-Ohm, |
| − | (10) Resistor 10K-Ohm | + | (10) Resistor 10K-Ohm, |
| − | (2) Photoresistors | + | (2) Photoresistors, and |
| − | (1) 10K Rotary Potentiometer | + | (1) 10K Rotary Potentiometer. |
====Misc Components==== | ====Misc Components==== | ||
| − | (1) Temperature Sensor | + | (1) Temperature Sensor, |
| − | (1) Temperature Sensor (covered) | + | (1) Temperature Sensor (covered), |
| − | (1) Piezo Buzzer | + | (1) Piezo Buzzer, |
| − | (3) Mini Push Buttons | + | (3) Mini Push Buttons, |
| − | (2) SPDT Switch | + | (2) SPDT Switch, |
| − | (1) SPDT Relay | + | (1) SPDT Relay, |
| − | (1) NPN Transistor | + | (1) NPN Transistor, |
| − | (1) PIR sensor | + | (1) PIR sensor, |
| − | (1) Pancake Vibration Motor | + | (1) Pancake Vibration Motor, |
| − | (1) Micro Servo | + | (1) Micro Servo, and |
| − | (1) Serial OLED LCD,0.96" | + | (1) Serial OLED LCD,0.96". |
Revision as of 15:30, 23 December 2016
This is a page where we can make notes about using the "Particle" device called the "photon."
Particle
Main page: https://www.particle.io/
Store: https://store.particle.io/
Photon Maker Kit
We have purchased 2 "Photon Maker Kits" (https://store.particle.io/collections/shields-and-kits)
The contents of this kit is shown below and is dicussed here: https://docs.particle.io/datasheets/particle-shields/#photon-maker-kit-contents
Basics
(1) Photon with Headers, (1) USB Micro B Cable, (1) Flex antenna, (1) Breadboard, (1) Proto-board, (1) Deluxe Jumper Wire Pack, (10) Male to Female Jumper Wires, and (1) Battery holder (4xAA, 2x2 with switch).
Headers
(5) 12-Pin Female Headers and (2) 40-Pin Male Breakaway Headers.
Capacitors
(10) Ceramic Capacitor 10nF, (10) Ceramic Capacitors 100nF, and (5) Electrolytic Capacitors 100uF.
LEDs and Diodes
(5) Basic LED - Red, (5) Basic LED - Green, (1) RGB LED, (6) Diode, and (1) IR LED.
Resistors
(10) Resistor 220-Ohm, (10) Resistor 1K-Ohm, (10) Resistor 10K-Ohm, (2) Photoresistors, and (1) 10K Rotary Potentiometer.
Misc Components
(1) Temperature Sensor, (1) Temperature Sensor (covered), (1) Piezo Buzzer, (3) Mini Push Buttons, (2) SPDT Switch, (1) SPDT Relay, (1) NPN Transistor, (1) PIR sensor, (1) Pancake Vibration Motor, (1) Micro Servo, and (1) Serial OLED LCD,0.96".