Difference between revisions of "Photon Development"
(Created page with "This is a page where we can make notes about using the "Particle" device called the "photon." Main page: https://www.particle.io/ Store: https://store.particle.io/ We have...") |
|||
| Line 1: | Line 1: | ||
This is a page where we can make notes about using the "Particle" device called the "photon." | This is a page where we can make notes about using the "Particle" device called the "photon." | ||
| + | ===Particle=== | ||
Main page: https://www.particle.io/ | Main page: https://www.particle.io/ | ||
Store: https://store.particle.io/ | Store: https://store.particle.io/ | ||
| + | ===Photon Maker Kit=== | ||
We have purchased 2 "Photon Maker Kits" (https://store.particle.io/collections/shields-and-kits) | We have purchased 2 "Photon Maker Kits" (https://store.particle.io/collections/shields-and-kits) | ||
| − | The contents of this kit | + | The contents of this kit is shown below and is dicussed here: https://docs.particle.io/datasheets/particle-shields/#photon-maker-kit-contents |
| + | |||
| + | ====Basics==== | ||
| + | (1) Photon with Headers | ||
| + | (1) USB Micro B Cable | ||
| + | (1) Flex antenna | ||
| + | (1) Breadboard | ||
| + | (1) Proto-board | ||
| + | (1) Deluxe Jumper Wire Pack | ||
| + | (10) Male to Female Jumper Wires | ||
| + | (1) Battery holder (4xAA, 2x2 with switch) | ||
| + | |||
| + | ====Headers==== | ||
| + | (5) 12-Pin Female Headers | ||
| + | (2) 40-Pin Male Breakaway Headers | ||
| + | |||
| + | ====Capacitors==== | ||
| + | (10) Ceramic Capacitor 10nF | ||
| + | (10) Ceramic Capacitors 100nF | ||
| + | (5) Electrolytic Capacitors 100uF | ||
| + | |||
| + | ====LEDs and Diodes==== | ||
| + | (5) Basic LED - Red | ||
| + | (5) Basic LED - Green | ||
| + | (1) RGB LED | ||
| + | (6) Diode | ||
| + | (1) IR LED | ||
| + | |||
| + | ====Resistors==== | ||
| + | (10) Resistor 220-Ohm | ||
| + | (10) Resistor 1K-Ohm | ||
| + | (10) Resistor 10K-Ohm | ||
| + | (2) Photoresistors | ||
| + | (1) 10K Rotary Potentiometer | ||
| + | |||
| + | =====Misc Components==== | ||
| + | (1) Temperature Sensor | ||
| + | (1) Temperature Sensor (covered) | ||
| + | (1) Piezo Buzzer | ||
| + | (3) Mini Push Buttons | ||
| + | (2) SPDT Switch | ||
| + | (1) SPDT Relay | ||
| + | (1) NPN Transistor | ||
| + | (1) PIR sensor | ||
| + | (1) Pancake Vibration Motor | ||
| + | (1) Micro Servo | ||
| + | (1) Serial OLED LCD,0.96" | ||
Revision as of 15:27, 23 December 2016
This is a page where we can make notes about using the "Particle" device called the "photon."
Particle
Main page: https://www.particle.io/
Store: https://store.particle.io/
Photon Maker Kit
We have purchased 2 "Photon Maker Kits" (https://store.particle.io/collections/shields-and-kits)
The contents of this kit is shown below and is dicussed here: https://docs.particle.io/datasheets/particle-shields/#photon-maker-kit-contents
Basics
(1) Photon with Headers (1) USB Micro B Cable (1) Flex antenna (1) Breadboard (1) Proto-board (1) Deluxe Jumper Wire Pack (10) Male to Female Jumper Wires (1) Battery holder (4xAA, 2x2 with switch)
Headers
(5) 12-Pin Female Headers (2) 40-Pin Male Breakaway Headers
Capacitors
(10) Ceramic Capacitor 10nF (10) Ceramic Capacitors 100nF (5) Electrolytic Capacitors 100uF
LEDs and Diodes
(5) Basic LED - Red (5) Basic LED - Green (1) RGB LED (6) Diode (1) IR LED
Resistors
(10) Resistor 220-Ohm (10) Resistor 1K-Ohm (10) Resistor 10K-Ohm (2) Photoresistors (1) 10K Rotary Potentiometer
=Misc Components
(1) Temperature Sensor (1) Temperature Sensor (covered) (1) Piezo Buzzer (3) Mini Push Buttons (2) SPDT Switch (1) SPDT Relay (1) NPN Transistor (1) PIR sensor (1) Pancake Vibration Motor (1) Micro Servo (1) Serial OLED LCD,0.96"