Difference between revisions of "Doc Kieft Monmouth Summer Research 2019"

From MC Chem Wiki
Jump to navigation Jump to search
Line 7: Line 7:
 
[[Caffeine_Standards|Caffeine Standards]]
 
[[Caffeine_Standards|Caffeine Standards]]
  
==Making the Coffee==
+
'''Making the Coffee'''
  
 
To make the coffee for the samples, 2.6 oz of beans were weighed out. These beans were then grinded, and 38 g of the beans were placed into a pourover filter. Then, 640 g of boiling hot water were poured over the grounds, allowing the grounds to bloom as needed. This process was done with both L0 and L5 beans.
 
To make the coffee for the samples, 2.6 oz of beans were weighed out. These beans were then grinded, and 38 g of the beans were placed into a pourover filter. Then, 640 g of boiling hot water were poured over the grounds, allowing the grounds to bloom as needed. This process was done with both L0 and L5 beans.
Line 13: Line 13:
 
After this first round of coffee, we discovered that the coffee samples were too concentrated for our standards, so we cut the amount of beans to 30 g of L0 and L5. This round we also made a sample of 15 g of the green coffee beans with 320 g of boiling water. We used a 0.45 micron filter and syringe to put this solution into the HPLC vials to ensure there was no particulate matter present.
 
After this first round of coffee, we discovered that the coffee samples were too concentrated for our standards, so we cut the amount of beans to 30 g of L0 and L5. This round we also made a sample of 15 g of the green coffee beans with 320 g of boiling water. We used a 0.45 micron filter and syringe to put this solution into the HPLC vials to ensure there was no particulate matter present.
  
==Instrumentation==
+
'''Instrumentation'''
  
 
After making the standards, we tested the standards using the HPLC to see where the peaks were for the different concentrations of caffeine. The following link goes into more depth about working with the HPLC.
 
After making the standards, we tested the standards using the HPLC to see where the peaks were for the different concentrations of caffeine. The following link goes into more depth about working with the HPLC.

Revision as of 20:11, 3 June 2019

Coffee Project

Project Overview

For this project I worked with Brad and a fellow student,Josie Welker, to determine the caffeine levels in different samples of coffee. For this project we made caffeine standards to compare the samples to. The following link describes how we made these standards.

Caffeine Standards

Making the Coffee

To make the coffee for the samples, 2.6 oz of beans were weighed out. These beans were then grinded, and 38 g of the beans were placed into a pourover filter. Then, 640 g of boiling hot water were poured over the grounds, allowing the grounds to bloom as needed. This process was done with both L0 and L5 beans.

After this first round of coffee, we discovered that the coffee samples were too concentrated for our standards, so we cut the amount of beans to 30 g of L0 and L5. This round we also made a sample of 15 g of the green coffee beans with 320 g of boiling water. We used a 0.45 micron filter and syringe to put this solution into the HPLC vials to ensure there was no particulate matter present.

Instrumentation

After making the standards, we tested the standards using the HPLC to see where the peaks were for the different concentrations of caffeine. The following link goes into more depth about working with the HPLC.

HPLC

Once the standards were tested, another HPLC trial was done including the L0 and L5 coffee samples.

An additional HPLC trial was done with coffee that was not as concentrated. This set included L0, L5, and the green coffee bean samples.